How to stretch or shrink a silicone phone case? How to make a phone case from scratch

The cell phone case is a little inappropriate in size. How to stretch it?

My cell phone case didn't fit a bit. That is, the mobile phone fit in there by tension. At the same time, the buttons turned on and the display lit up. I solved this problem by wrapping the phone in paper and putting it in a case overnight. You can add paper as you stretch the cover and increase its size. After two or three weeks the problem was resolved.

To stretch a leather case, make a model of your phone from a piece of wood (the thickness should be slightly thicker than the phone), split it in half lengthwise and insert them into the case. Between the halves, insert a plastic insert of the thickness to which you want to stretch the phone and put it in a jar of warm water for a day (you can put the jar on the battery). Remove the case from the water and air dry.

Alternatively, instead of water, you can use alcohol to significantly reduce the drying time.

Why a tab? Because after drying, the cover can compress the model so much that it will be impossible to remove the piece of wood. In addition, the tree will also swell from water. And plastic, even sandwiched between pieces of wood, can easily be pulled out. Just remember to make the insert long enough so that you can grab onto it later.

Don't want to bother making a layout? There is an easy way, but the quality is not guaranteed.

Just insert pencils, felt-tip pens, round rods, etc. inside the case along the edges. of the appropriate diameter, and push a rectangular piece of a suitable size between them with tension. The rest is the same as described above.

• How to stretch a leather phone case?

  1. Soak in an alcohol-glycerin solution.
  2. Insert a piece of wood into the cover of the shape to which you want to stretch the cover. Wait a day.

  How to stretch a silicone case?

  1. Soak in hot water.
  2. Immediately after heating, place on a wooden mold.

Some people buy a case to decorate their phone, while others buy it to protect the case from scratches and damage. And sometimes a situation arises when you like a mobile phone accessory, but the size doesn’t fit. How to stretch a case without damaging it? To solve this problem, you need to take into account its shape and the material from which it is made. Read more about it.

It is not difficult to stretch a leather case

How to stretch a leather case

A leather case that does not fit on the phone or fits too tightly, causing the buttons to operate, it is advisable to enlarge it a little. The leather stretches well if it is wetted with water, and when dried it retains its given shape, so use a simple method.

• Try to select or cut a piece of wood that is the same size as the mobile.
• Split the resulting workpiece in half along the flat side. Insert a thin plastic plate into the slot.
• Wet the cover well in warm water and stretch it onto a wooden model.
• Leave it to air dry without heat, otherwise the leather will dry out and crack.
• After about a day, when the cover is dry, remove the plate, and then the wooden block.

The accessory will stretch to the desired size. If you use a mixture of alcohol and glycerin instead of water, the drying time will be reduced, the procedure will be more gentle on the skin, and the surface will retain its shine.

How to stretch a silicone case

Silicone is a fairly durable and elastic material. There are many covers available from it, so you can always choose the right option. If desired, buy an accessory - a bumper, which is easier to put on and does not require selecting the location of the connectors.

But there are still times when it is necessary to stretch the silicone case. You can do it like this.

• Considering the property of silicone to stretch over time, you can crush it with your hands and pull it to the sides. If the size doesn't fit just a little, you'll soon be able to put it on.
• After heating, the silicone becomes more flexible, and it is easier to pull the case onto the phone. You can use a hairdryer here.
• If there is a large difference in size, stretching on a wooden model is suitable. The cover must be heated in hot water, pulled onto a prepared block, heated for an hour in water and cooled in air. The disadvantage of this method is that the silicone can stretch too much and will dangle on the phone.

The desire to beautifully decorate your phone arises in everyone who visits the website of the online store https://itsellopt.com.ua/ at the sight of attractive cases and bumpers. But not all of them can provide the communication device with adequate protection in the event of an impact or fall. And if the range includes a shock-absorbing bumper for your phone, it will either not be suitable for your model, or its cost will be astronomical. There is only one way out - to spend a little time, imagination, effort and make a beautiful case from scrap materials.

Everyone has a desire to decorate their phone.

The colorful bumper can be made from silicone to make molds without touching brushes or glue.

To prepare the material you will need:

• Construction silicone;
• Potato starch as a thickener and to give white color;
• Color or acrylic paint.

It is better to use silicone gloves during the kneading process. This way, your hands will feel the material, and you won’t have to wash them for a long time.

Manufacturing technology:

1. After squeezing out the silicone, you need to add two tablespoons of potato starch to it.
2. The process of kneading silicone “dough” is similar to the preparatory stage before modeling from plasticine. It needs to be kneaded until the mass becomes homogeneous.
3. If you divide the resulting mass into several almost equal pieces and add a color to each of them, you will get multi-colored balls. They need to be flattened, folded so that each previous one peeks out from under the previous flat cake by a few millimeters.
4. Using a rolling pin, roll out the workpiece so that it is enough to cover the back wall of the gadget, its edges and a small bend on the front side.
5. The phone is wrapped in the resulting multi-colored or plain sheet of silicone.
6. It needs to be pressed a little into the “dough” to mark the holes for the camera and speaker grille, located on the back side.
7. Connectors and control buttons on the side elements of the phone must be marked by running your thumb along the entire perimeter of the phone.
8. The silicone should harden. Its readiness time depends on the thickness of the rolled layer and the data provided by the manufacturer.
9. It is better to remove excess silicone immediately using a stack or a plastic knife. Without excess material it is easier to form the corners.

Advice! Hardening of the silicone mass can take up to 12 hours. Move the SIM card to another phone or forward calls. Otherwise, the cover will not have a smooth surface.

Gallery: bumper and phone case (25 photos)

How to make a silicone bumper with your own hands (video)

How to make a clear phone case

The easiest way to put your phone in a transparent case that protects only from moisture and dust is to use a piece of heat-shrinkable film. You can find the starting material at any grocery store. It comes with glass jars containing canned food.

You can find the source material in any grocery store.

Cut out a rectangle from the film so that it is 1.5-2 cm larger than the phone on each side. When folding the film onto the front side of the phone, it must be heated with the flame of a lighter. Only the flame should not touch it. The evenly applied film will become the skin of the gadget. It can only be removed with scissors. But that will be much later. In the meantime, a manicure set will be needed to cut holes for the camera, side buttons, charger and headphones.

Transparent silicone case

To make a transparent silicone case, you will need the appropriate quality material. Silicone sealant for gluing glass is best suited for this purpose. Its setting time is 30 minutes.

To work you will need:

• Box. The one in which the phone was sold will do.
• Soft plasticine or modeling dough.
• Polyethylene film to protect the phone from contact with materials - plasticine and uncured sealant.

Step-by-step instruction:

1. The box is filled one third with plasticine or dough.
2. The phone is placed in a thin plastic bag.
3. It must be placed in the middle of the plasticine pillow and pressed evenly to create a shape 2-3 mm deeper than the thickness of the phone itself.
4. The resulting form must be coated with an even layer of sealant.
5. Place the phone back into the hole it made.
6. The silicone squeezed onto the surface can be slightly leveled, giving it the shape of the future case.
7. After the material has dried, the phone and the bumper are removed from the mold. Cleaned from plasticine and polyethylene.

Advice! If the protective layer of the cover is planned to be thicker than 3 mm, then the recess in the plasticine mold must be made deeper.

How to decorate a silicone case

Decorating the silicone case can be done during the manufacturing process.

1. You can insert small rhinestones in the form of your own initials, outlines of animal faces and other simple ornaments into the thick silicone transparent layer.
2. Glitter is added to silicone during the process of coating the mold with it or preparing the “dough” before rolling out. In the first case, shiny crumbs can be poured through a strainer, which is necessary for even distribution. In the second, it is better to mix them with potato starch.
3. Adhesive-based rhinestones will allow you to create an original decoration on the back wall of the bumper.
4. The most original and unique silicone cases are obtained when decorated with dotted patterns made with acrylic paints. The material in small tubes with dispensing spouts can be purchased at craft stores. You can draw and decorate any design for the case yourself.

The easiest way to decorate is to find a beautiful picture in the desired format and insert it between the phone and the case. It makes for great decor.

How to make a phone case from a balloon

The technique for creating such a bumper is similar to vacuum packaging a phone in latex.

1. The balloon is inflated to medium size.
2. It must be laid on a flat surface, holding the neck with two fingers.
3. Place the phone in the middle.
4. The gadget must be slightly pressed down and the air must be released from the ball.
5. A couple of minutes of work, and the phone is dressed in a new bright shirt.
6. All that remains is to cut holes for the camera and connectors, and the thin material will not interfere with the operation of the buttons.

The technique for creating such a bumper is similar to vacuum packaging a phone in latex.

Paper smartphone case

A cover-book made from vinyl wallpaper is made according to the principle of a box.

To do this you need to take:

• Ruler;
• Pencil;
• Scissors;
• Glue.

The case can also be made using origami

Making the case:

1. On a sheet of paper, moving 1 cm from the edge with an increase in the thickness of the side wall, trace the outline of the phone.
2. Departing from Figure No. 1 to a distance equal to the thickness of the device + 1 mm, the phone is circled a second time.
3. The wall thickness is also added at the top and bottom + 1 cm.
4. Using nail scissors or a blade, cut out holes for the charger, headphones, camera lens, and screen.

The same bumper, made of corrugated cardboard, will provide excellent protection for the phone during impacts and falls. The only thing is that decorating it is more difficult. It can be painted and a dense dot pattern applied to it using acrylic paints. But this will not protect the paper from getting wet when it rains.

You can independently increase the moisture resistance of paper or cardboard using lamination. To make a homemade case both beautiful and moisture-resistant, you first need to cut it out, paint it, laminate it, and only then assemble it.

Is it possible to make the rubber boot smaller?

During use, the rubber covers stretch. They can be returned to their original size. To do this, they must be immersed in boiling water. They will become more plastic, and when cooled they should return to their original size.

Some bumpers, made of rubber with a large proportion of plastic, are not as flexible as rubber. But they can also be made smaller at home. If immersing the cover in boiling water does not lead to the expected result, you can try boiling it for 5 minutes - the principle of preparing a polyethylene suction cover. He works. Just don’t put a wet bumper on your phone; the moisture needs to be removed from it.

Making a Coca-Cola case (video)

(No ratings yet)

Then most likely you purchased a low-quality accessory from a dubious seller on an advance payment or received such an unpleasant surprise included with a smartphone from China.

Although this is not pleasant, you can still try to restore the silicone case. Why try? Yes, because it is not known how a particular cover will behave during heat treatment, and yet some bumpers can be restored in size and bent edges corrected.

It is worth immediately noting that in this article we are talking about covers made of thermoplastic polyurethane (TPU), this is the main material for the production of bumpers today, however, there are other material options, and it is difficult to predict how they will behave when processed in this way.

Restoration of shape by thermal method

Most often, this kind of deformation and stretching occurs when the covers are transported carelessly or when stored in improper conditions without a special damper insert. Such cases take an irregular shape and do not fit tightly on the smartphone. However, if such an accessory was made exactly to size, this can be corrected.

To restore the cover, we need two containers of water; it is very important that the size of the containers used is larger than the size of the cover itself. If you place the case in a small container, you risk deforming the accessory even more.

In the first container, you need to bring the water to a boil and leave it on low heat, and in the second, the water should be as cold as possible.

Dip the stretched cover into boiling water and hold for up to 5 minutes (time depends on the thickness of the cover). After the cover has warmed up well enough, transfer it to cold water, and if there are any deformations on the edges of the bumper, straighten them with your hands and in this position lower them into cold water.

Such a sudden change in temperature can cause a slight decrease in size, but if the case has a significant deviation in size, you most likely will not be able to reduce it.

How to buy a quality case?

Defects in accessories happen in any store, even the most famous ones, but the approach to solving the problem is the hallmark of good stores.

If you are forced to choose a case online and are unable to try it on and hold it in your hands before purchasing, you can always use the cash on delivery service. This service is provided by most delivery companies in Ukraine. And suspicious sellers who refuse to send you goods in this way should immediately arouse your suspicion.

Most likely, they are selling a low-quality product and are afraid that you will refuse it.

It often happens that it is not profitable for you, as a buyer, to pay the cost of delivery, and even the cost of the cash on delivery service, but the online store site meets you and pays for the delivery of any goods at its own expense. You can order a high-quality cover at a very inexpensive price, try it on at a Nova Poshta branch before paying, and at the same time not overpay inadequate amounts.

Return or exchange guarantee

A money-back or exchange guarantee for defective goods can be very useful, most good stores are required by law to adhere to this rule and provide you with such a guarantee for a period of 14 days. However in the online store website such a guarantee is as much as 25 days! This is an opportunity to test the product in practice, without risking losing your money.

Please note that unscrupulous sellers also write about this guarantee, but they use free ad services and one-page sites to distribute their goods, since you will not be able to check reviews about such a seller or complain anywhere.

When choosing a reliable store, pay attention to the presence of a real address, reviews using authorization through social networks and high-quality advice on the issue that interests you.

Ask if you can come and see the product at the specified address? If the seller refuses to show you the product and insists on sending it with advance payment or partial payment, he is most likely a scammer.

Our online store also has a channel on YouTube, and you can see what the type of case you are interested in looks like.

Even a silicone case purchased for a specific phone model may not be the right size. If it was sent through an online store or purchased without “trying on”, then returning the product may be difficult. In this case, it becomes necessary to take action on your own. In this article we will look at how to stretch silicone or, conversely, compress it using available means.

How to stretch a silicone phone case

Silicone is a fairly durable material, which at the same time is very elastic. The latter property is associated with a significant disadvantage of such covers - they stretch over time. Well, if you want to speed up the process and increase the size of the overlay immediately, there are several effective ways:

The presented methods will help to cope with the problem of a small case if its size needs to be increased by 1-3 mm.

How to make a silicone case smaller

As already mentioned, silicone has a significant drawback - it stretches after some time of use. For this reason, the question arises of what to do if the silicone case is stretched. You can try to reduce it using the method below. The presented method has been tested by many people and is guaranteed to help solve the problem.

Before taking specific actions, you should know that the size will decrease by 1-2 mm. If the cover is very loose, then it is better to buy a new one and not waste your time. In case of a minor sprain, the following steps must be taken:

• Choose a pan that will allow you to completely fit the lining without touching the edges. Pour water into it and put it on the stove to heat.
• Bring water to a boil and place the accessory in it.
• Cook the lining for about 5-7 minutes, holding it with a fork so that the water completely covers the material.
• Remove from the pan and leave to cool completely.
• Wipe dry and try on the phone - the case has shrunk and fits tightly to the body.

Before performing the procedure, it is important to pay attention to the material of the lining. If the polymer alloy is transparent, it will become cloudy, but real silicone will not change its properties. However, for opaque accessories this does not matter. Some users note that they were able to partially restore transparency by placing the case on the battery for a while.